CCIE SP Cable Qualification Exam : 350-021 Exam

Exam Number/Code: 350-021
Exam Name:CCIE SP Cable Qualification Exam

“CCIE SP Cable Qualification Exam”, also known as 350-021 exam, is a Cisco certification. With the complete collection of questions and answers, Actualtests has assembled to take you through 399 questions to your 350-021 Exam preparation. In the 350-021 exam resources, you will cover every field and category in CCIE helping to ready you for your successful Cisco Certification.
Free Demo DownloadActualtests offers free demo for 350-021 exam (CCIE SP Cable Qualification Exam). You can check out the interface, question quality and usability of our practice exams before you decide to buy it.

Exam DetailsThe written exam is a two-hour, multiple choice test with 100 questions covering areas such as Layer 2 networking, IP protocols, MPLS, VPN, security, quality of service and high availability technologies. The exam is closed book and no outside reference materials are allowed.

Free Sample :PassGuide-it certification Printable PDF Or software Download: Actualtest offers free demo for IT certification Exams You can check out the interface, question quality and usability of our IT Simulation exams before you decide to buy it. We are the only one site can offer demo for almost all products http://demo.passguide.com/download

QUESTION 11:
Which are functions of the Domain identifier Assigned (DIA) ILS? Select two
A. It indicates that a Principal Switch has been selected, and that the upstream neighbor Switch
has been assigned a Domain identifier.
B. It indicates that the receiving Switch can proceed requesting a Domain Identifier.
C. It indicates that the principal switch selection and address assignment phase is completed and
the fabric is operational.
D. It indicates that the principal switch selection is started, but a principal switch has not been
identified yet.
E. It indicates that a Request Domain Identifier ILS has been received by principal switch.
Answer: A, B
QUESTION 12:
What zoning option can be used in interop mode 2 and 3?
A. domain / port
B. nWWN
C. fcid
D. lin zoning
E. sWWN
Answer: A
QUESTION 13:
You have a legacy JBOD that uses copper DB-9 connecters. You want to connect
your JBOD to a Fiber only Fiber Channel switch. You want to convert the DB-9
connection to multi mode Fiber Optics. What device would you use?
A. HSSC
B. MIA
C. GBIC
D. SFP
E. DUAL SC
Answer: B
QUESTION 14:
FCIP Write Acceleration most effectively addresses which disaster recovery
challenge?
Actualtests.com – The Power of Knowing
A. Recovery Time Objective (time to recover)
B. Recovery Point Objective (time DR data is “behind” Production data)
C. Tape backup over the WAN
D. Load balancing
E. Bandwidth constraints
Answer: C
QUESTION 15:
What port type can be used on a Fiber Channel switch when connecting a Fiber
channel Hub that has one host attached to the hub and it is on a public network?
A. Fabric Loop
B. FLP
C. F
D. Loop Fabric
E. TL
Answer: A
=> public loop: FL port
QUESTION 16:
What are the 3 types of Ordered Sets defined in Fiber Channel?
A. Offline sequence, online sequence, and link reset
B. Start of frame, end of frame, and idle
C. Frame delimiters, primitive signals, and primitive sequences
D. K28.5, D16.0,and D31.2
E. None of the above
Answer: C
=> ordered sets: Frame delimiters, primitive signals, and primitive sequences
QUESTION 17:
Hosts and storage are connected to 2 MDS units interconnected by lSLs in the
following manner:
FCID Initiator/Target MDS VSAN Zone
0×01000a initiator 1 1 A
0×01000b Target1 1 B
0×01000c initiator 2 2 A
0×02000a Target2 1 A
0×02000b initiator 2 1 B
Actualtests.com – The Power of Knowing
0×02000c Target1 2 A
All default zones are set to deny and IVR is not enabled. Trunking is disabled on all
of the lSLs, which reside in VSAN 1. How many pairs of sourc-destination flows are
possible over the ISLs in this configuration?
A. 1
B. 2
C. 3
D. 4
E. 5
Answer: B
=> domain pairs [0x0100a,0x0200c]zoneA, [0x01000b,0x02000b]zoneB
QUESTION 18:
When using Fcanalyzer to capture a flow from FCID 010300 what would be the
proper command?
A. Can not filter at FCID level on Fcanalyzer
B. MDS#fcanalyze local display-filter
(mdshdr.vsan==1)&&((fc.d_id==01300)or(fc.s_id==01300))
C. MDS(config)#fcanalyze locaal display-filter
(mdshdr.vsan==1)&&((fc.d_id==01300)or(fc.s_id==01300))
D. MDS(config)#fcanalyze display-filter
(mdshdr.vsan==1)&&((fc.d_id==01300)or(fc.s_id==01300))
E. MDS(config)#fcanalyze display-filter
(mdshdr.vsan==0×01)&&((fc.d_id==01300)or(fc.s_id==01300))
Answer: C
=> fcanalyzer config: MDS(config)#fcanalyze local display-filter ~~~
QUESTION 19:
Which are true about the advertisement methods for Iscsi targets implemented by
the MDS 9000? Select two.
A. By default, Iscsi TARGETS ARE ADVERTISED ON ALL gigabit Ethernet interfaces
and subinterfaces.
B. By default Iscsi TARGETS ARE NOT ADVERTISED AND THE
ADMINISTRATOR CAN CHOOSE WHETHER TO ADVERTISE THEM OR NOT
BY CHANGING THE SWITCH CONFIGURATION.
C. By default, Iscsi targets are advertised only on Gigabit Ethernet interfaces but not on
subinterfaces.
D. By default, Iscsi targets are advertised on Gigabit Ethernet subinterfaces only but not
on the main Gigabit Ethernet interfaces.
Actualtests.com – The Power of Knowing
E. It can be limited by the administrator by configuring the Gigabit Ethernet interfaces
over which static iSCSI targets are advertised.
Answer: A, E
Explanation:
=> iSCSI target advertise method:
QUESTION 20:
What standard association is working in the definition of the Iscsi and Fiber
Channel protocols respectively?
A. SNIA and IETF
B. FCIA and IETF
C. IETF and ANSI
D. FCIA and SNIA
E. SNIA and T11
Answer: C

Free download:pass4sure CCIE 350-021
Free download?testking CCIE 350-021a>

Download Free PassGuide Product, Help you pass any it Exams,Click Me

Actualtests Free Downloads

Type	Exam Bible	NEW Questions & Answers	Latest Updated	Download link
	All Actual-Test 's Exam Pack	858	1 days ago	Full Download

Download Free Latest Actualtests Certification Braindumps

1. Free Actualtest Actualtests CCIE 350-029
2. Free Actualtest Actualtests CCIE 350-023
3. Free Actualtest Actualtests CCIE 350-024
4. Free Actualtest Actualtests CCIE 350-020
5. Free Actualtest Actualtests CCIE 351-001
6. Free Actualtest Actualtests CCIE 352-001
7. Free Actualtest Actualtests CCIE 350-040
8. Free Actualtest Actualtests CCIE 350-018
9. Free Actualtest Actualtests CCIE 350-025
10. Free Actualtest Actualtests CCIE 351-018